0	Hull type has no rows or columns.

# Creep
1	The input source or the path surface has zero area
2	The path is not a surface.

# Group 

3	There are less than two groups specified.

# Lattice
4	%s geometry bounding divisions do not match lattice divisions.
5	Invalid rest position data.

# Lsystem
6	Tree aborted.  It is too complex.
7	Tree aborted.  Rules cause stack underflow.

# Magnet
8	No effect.  The scale or rolloff value is zero.

# Rails 

9	Cannot attach primitive %s to the two points
10	The geometry in the cross-section has no points	
11	The connection vertices exceed the number of cross-section vertices
12	There is no geometry in the cross-section
13	The geometry for the rail has no points
14	Could not construct the rail polygon from Bezier/NURBS curve
15	Please use at least two rails. 

# Sweep 

16	The backbone doubles back on itself
17	Cannot compute the dihedral
18	Could not construct the sweep polygon from Bezier/NURBS curve
19	The first and last points are the same
20	The backbone doubles back on itself
21	Cannot connect primitive %s as it is not a polygon, Bezier curve or NURBS curve. 
22	The connection vertex exceeds the number of cross-section vertices in primitive %s

# Skin
23	Some primitive types in the source geometry cannot be skinned. 
24	Unable to skin the given primitives:  Cannot wrap with less than 3 rows.
25	The order is greater than the number of rows	
26	Bad input type
27	The surface cannot be built with the given parameters
28	Cannot skin primitives of different types. Use the convert SOP to convert to one type. 
29	Primitives have different point counts. Try inserting a refine SOP.

# Font
30	The font is not valid

# Grid
31      The surface type is invalid for 1 row or 1 column. Try using another surface type. 

# Twist
32      Primary and Secondary axis cannot be the same.

# Extrude
33	Cannot extrude faces with less than 3 points.
34	Can only extrude polygons, Bezier or NURBS curves.
35	The xsection can only be a face type. (polygons, Bezier, or NURBS curves)

# Loft
36	Unable to loft primitive(s).
37	Encountered faces of different types. Try converting first.
38	Spline curves have different degrees.
39	Some primitives are not face or hull types.

# Caps
40	Face cap cannot be built with the given parameters.
41	Shared caps is not possible with non-wrapped non end-interpolating 
41	NURBS surfaces.  This is an approximation.
42	A tangential cap is not possible on this topology.  A rounded 
42	cap with scale zero may be equivalent.

43	The geometry has not been changed.  The magnet needs 
43	to be a meta primitive.  (i.e. MetaBall, MetaSuperQuadric)	

# font table
44	Aborted reading font table. There was probably an incomplete entry.

# interpolation
45	Resulted in a singular system of equations. Can not be solved. 
45	Please make sure there are no coincident points.

# imperfect primitive
46      The curve was reduced to order %s for the given parameters
47      The surface was reduced to vertical order %s for the given parameters
48      The surface was reduced to horizontal order %s for the given parameters

# join
49	Bad join type(s): Primitives are not only faces or only hulls.

#fractal
50	Insufficient memory for the given parameters.  Try reducing the divisions.

#fillet
51	Can only fillet a set of faces or a set of hulls.
52	A single primitive cannot be partially filleted to itself.

#stitch
53	Can only stitch a set of faces or a set of hulls.
54	The auxiliary secondary input must be a hull.

#sweep
55	Bad Reference Path - double back on itself
56	Reference path must have the same number of points as backbone.
57	Reference path must have the same number of primitives as backbone.

#curveclay
58	The given profiles cannot form a loop
59	The length of deformation is zero
60	No profiles found
61	The number of evaluation divisions is zero
